How To Tie A Leather Belt

Download Commodity

Download Article

In Judo, practitioners wear a uniform called a "gi," which is held by a belt called an "obi." If you're just starting out in Judo, you may have a bit of trouble learning how to tie your obi yourself. Fortunately, whether you're tying a traditional knot or a competition knot, learning to tie an obi can exist equally piece of cake as tying your shoe once you've learned the specific steps to follow.

1. 

   1

   Place the middle of the chugalug on your abdomen button. You can notice the eye of the belt by letting the 2 ends of the belt dangle to the floor. The two sides of the belt should exist equal in length when you hold information technology up to your belly button.

   • It's very important to take both sides of the belt be equally long in order to necktie your knot properly.

2. 

   2

   Run the belt around your back, crossing the 2 strands over each other. Accept the left terminate of the belt in your correct mitt one time it'southward behind your back, and vice versa. Then, pull your hands frontward to bring the ends of the belt dorsum to the front of your body.^[1]

   • The signal where the ii strands cantankerous over each other should be located just above the small of your back.

   Ad

3. 

   3

   Cross the left end of the belt over the right cease. Lay the right cease of the belt over your belly push button starting time, and so lay the left finish over top of it. The belt should resemble an "X" later y'all do this.^[ii]

   • Make sure the 2 strands of the belt are still even in length before crossing them over each other here.

4. 

   four

   Loop the new correct end under the belt and pull it out of the pinnacle. Do this with the end of the belt that is at present located on the right side of your body. The stop of the belt should end up above your belly button but still on your correct side.^[iii]

   • Yous can give the two ends of the belt a slight tug at this point to make sure the belt is taut, although this isn't strictly necessary.

5. 

   v

   Cross the new right stop of the belt with the new left end. Simply lay the correct end over tiptop of the left terminate, creating an "10" with the 2 ends.^[4]

   • The 2 ends of the belt should be about equal in length equally they jut out from the heart of the "X."

6. 

   6

   Loop the correct end of the belt under the left and pull them both tight. Put your left paw under the belt to catch the correct end, then pull information technology up and through the loop. Finally, pull both ends of the belt at the aforementioned fourth dimension to end and tighten the knot.^[five]

   • If yous've tied the knot correctly, the 2 strands of the belt should still be equal in length.

Advertizing

1. 

   i

   Hold the chugalug and then that the correct end is 2 to 3 inches (5.1 to 7.half-dozen cm) shorter than the left. Place the belt in front of you lot and on height of your belly button when you do this. Having one end shorter than the other will requite yous enough actress length to wrap the chugalug around you lot twice.^[6]

   • You don't desire to leave the left stop too long, since this will make your knot lopsided when you go to tie it later.

2. 

   ii

   Wrap the long terminate of the belt around your back twice. Once the belt has been wrapped around you twice, brand sure the two strands in front end of you are equal in length. If they aren't, you'll need to kickoff over from the beginning and adjust your starting lengths.^[7]

   • The belt should exist wrapped on summit of itself in the back, with the left end of the chugalug crossing over the right cease on the right side of the front end of your body.

3. 

   3

   Accept the left cease of the belt and loop it under the entire belt. If yous wrapped your obi correctly, the left end of the belt should be the 1 on top. Use your right hand to push button the left stop nether the chugalug, and then use your left mitt to pull it all the way upwards and out.^[8]

4. 

   four

   Loop the bottom terminate of the chugalug betwixt the 2 chugalug layers in the front end. Bring the bottom terminate up and over the front of the belt, then insert it between the two layers. Exit a small loop on the top by not pushing the lesser end all the manner through.^[ix]

   • The loop doesn't need to be huge; it just needs to be big enough to allow 1 terminate of the belt to pass through it.

5. 

   5

   Put the height belt end through the small loop and betwixt the belt layers. Going from left to right, first push button the summit end of the chugalug through the pocket-sized loop made past looping the bottom end between the 2 chugalug layers. Then, push the superlative end between these layers and pull information technology downwards.^[ten]

   • Once this is done, pull both ends of the chugalug to tighten information technology.

Advertisement

Inquire a Question

200 characters left

Include your email accost to go a message when this question is answered.

Submit

Advertizing

• Don't beat yourself upward if your chugalug doesn't come out right on the first few tries! Your instructor will sympathize and will be willing to help you when you're first starting out.

Thanks for submitting a tip for review!

Advertising

Near This Article

Thanks to all authors for creating a page that has been read 40,846 times.

Did this commodity help you?

Source: https://www.wikihow.com/Tie-a-Judo-Belt

Share this post